Search
banner

Pulse Bag Filter: Complete Technical Specifications, Model Selection and Performance Parameters

Author:Daniel Foster Time:2026-11-19 11:56:56 Number of views:60Second-rate

A pulse bag filter is a continuous-duty dust collection device that cleans its fabric tubes inline with a short, high-pressure burst of compressed air, so the unit never stops for manual bag shaking. This reference is built around the numbers engineers need: housing dimensions, filter areas, air-to-cloth ratios, model capacities, media ratings and the operating limits that decide whether a unit meets emission targets and keeps meeting them for years. Treat the tables below as a specification worksheet for a real process.

Pulse Bag Filter

Pulse bag filter at a glance: core specification sheet

The table lists the typical value envelope for a mid-size pulse-jet baghouse before add-on options. Values are ranges because one family spans several chamber counts and bag lengths.

ParameterSymbolTypical rangeUnit / note
Air volume handledQ3,000 to 120,000m3/h, per unit
Total filter areaA30 to 2,400m2, by bag count
Air-to-cloth ratioAV0.8 to 3.5m/min, pulse-jet
Operating pressure dropDP1.0 to 2.0kPa, normal cake
Cleaning air pressurePc0.4 to 0.7MPa, at valve
Pulse durationTp0.08 to 0.15s, per blast
Inlet temperatureTiambient to 260deg C, media based
Filtration efficiencyE99.5 to 99.99% by weight
Bag diameterDb120 to 160mm, standard
Bag lengthLb2.0 to 6.0m, single tube

These figures are the starting point for sizing. The air-to-cloth ratio is the most influential number because it sets pressure drop, bag life and housing size together.

0.8-3.5Air-to-cloth ratio window (m/min)
1.0-2.0Operating pressure drop (kPa)
0.4-0.7Cleaning air pressure at valve (MPa)
99.5-99.99Filtration efficiency by weight (%)

Model series and capacity comparison

Manufacturers group pulse bag filters into series by chamber layout and bag arrangement. The comparison below maps common series classes to the duty they fit, so a specifier can shortlist a few families.

Series classFilter area (m2)Airflow (m3/h)Typical dutyFootprint
Single-chamber, 2 m bag30 to 1803,000 to 20,000Workshop welding, binsCompact, skid
Single-chamber, 3 m bag60 to 3606,000 to 40,000Woodworking, packagingMedium, indoor
Multi-chamber, 4 m bag200 to 1,20020,000 to 80,000Cement, grainLarge, outdoor
Multi-chamber, 6 m bag400 to 2,40040,000 to 120,000Mineral, chemicalVery large, modular
A larger bag length reduces the number of tube-sheet holes for a given area, lowering the leak risk at the clean side. It also raises the pulse energy needed to clean the full tube, so longer bags need a stronger cleaning system.

Selection parameter worksheet

The following table converts a process brief into the parameters a supplier quote should reference. Fill each row from measured plant data, because an understated airflow is the most common cause of a unit that never reaches spec.

Selection inputHow to determineDesign rule
Total gas flowSum all hoods, ducts and ventsAdd ten to fifteen percent spare
Dust load inletGravimetric sample at worstSize hopper for peak
Particle size spreadDiffraction or sieve testFiner median lowers safe AV
Peak temperatureLogger over full cycleMatch media to peak
Moisture and dew pointGas analysis at inletKeep metal above dew point
Abrasion / stickinessDust trait reviewChoose finish and inlet defence
Explosion classDust screening testAdd venting and isolation if needed
Target emissionPermit or internal limitSize AV and media for limit

Filter media data table

Media sets the temperature ceiling, chemical resistance and release. The table collects the reference envelope for common felts used in pulse bag filters.

MediaTemp ceiling (deg C)ReleaseChemicalTypical use
Polyester, scrim130GoodFairWood, grain, dry
Polyester, oil-water finish130Very goodImprovedMoist or oily dust
Polypropylene90GoodExcellentAcid, wet, chemical
Aramid200GoodGoodAsphalt, metal, hot
P84 / polyimide240Very goodGoodHigh-temp mineral
PTFE membrane260ExcellentExcellentFine, sticky, corrosive
Fiberglass with finish260FairGoodHigh temp flue gas
Antistatic blendmedia dependentGoodPer base fibreCombustible dust

90-260Media temperature ceiling (deg C)
8Common felt constructions listed
2Key axes: temperature and release
1Decision: match media to peak condition

Pulse cleaning system parameters

Cleaning energy is a short blast through a venturi at the bag mouth. The balance of supply pressure, pulse width, nozzle size and tube length decides whether the cake releases fully or merely compacts lower down the bag.

Cleaning variableSetting rangeEffect when raised
Supply pressure0.4 to 0.7 MPaStronger release, more air used
Pulse width0.08 to 0.15 sMore energy, over-clean risk
Pulse interval10 to 120 sLonger cake, higher DP
Nozzle diameter10 to 30 mmWider spread, better clean
Tank volumematched to blastsSteadier pressure
Sequencingrow by rowNeighbours keep filtering

A well-tuned sequence cleans one row at a time while the rest of the chamber keeps filtering, so total flow is hardly affected. Cleaning too often strips the protective cake and shortens bag life; cleaning too rarely lets pressure drop drift upward and can starve the fan.

Dimensional and layout parameters

Housing geometry affects both performance and installation cost. The layout table gives the proportional rules used when arranging tubes on the tube sheet and sizing the hopper beneath them.

DimensionRule of thumbReason
Tube spacing1.5 to 2.0 x diameterAvoid bag re-entrainment
Tube sheet thicknessmatched to flange loadStays flat, no leak
Hopper angle60 deg or steeperFree flow, no bridge
Inlet velocitybelow 18 m/sPre-settle coarse
Clean plenum height0.8 to 1.2 mEven flow to fan
Access walkwayminimum 0.8 mSafe access
Tube spacing that is too tight causes dust from one bag to land on a neighbour, raising the load and shortening the cleaning interval. Spend floor space on spacing before adding more bags.

Performance parameter comparison by dust type

The same hardware behaves differently across dusts. The table lists a recommended air-to-cloth starting point for several common materials.

Dust typeSuggested AV (m/min)Media noteWatch item
Wood sanding2.5 to 3.5Polyester, anti-staticFire, spark defence
Grain / flour2.0 to 3.0Polyester, food gradeExplosion venting
Cement / lime1.0 to 1.8Polyester or aramidAbrasion at inlet
Metal fume1.2 to 2.0PTFE or fine feltVery fine, sticky
Welding smoke1.5 to 2.5Polyester with finishOil and moisture
Chemical powder0.8 to 1.5PP or PTFECorrosion, reactivity

0.8-3.5AV range across dust types (m/min)
6Material classes compared
2.5xSpread between easiest and hardest dust
1Rule: finer dust needs lower AV

Compressed air and utility load

Pulse cleaning needs dry, oil-free air, or the media wets out and the cake packs. The utility table estimates air demand for the plant system.

Utility itemIndicative valueComment
Air per pulse0.02 to 0.08m3 per blast
Pulses per minute2 to 20By chamber size and load
Pressure dew pointat least 10 below minPrevents condensation
Oil contentbelow 1 mg/m3Protects media
Electric loadfan plus controlsFan dominates cost
Noise at valvetypically 85 to 100dB(A), silencer if near staff

Undersized or wet plant air is the hidden cause of many complaints. When valve pressure sags during a sequence, the last rows never get a full blast and pressure drop climbs until someone blames the bags.

Energy and operating cost parameters

Running cost is dominated by fan power, which scales with airflow and pressure drop. The figures show why holding pressure drop in range matters more than shaving the bag price.

Cost driverLeverEffect
Fan powerLower stable DPCuts electricity every running hour
Bag changeRight media and AVExtends interval, fewer stops
Compressed airTuned pulseLess wasted blast volume
DowntimeTrend monitoringFewer surprise outages
DisposalControlled captureCleaner, cheaper handling
A collector specified at a slightly lower air-to-cloth ratio costs more to build but can save more in fan energy over its service life than the extra fabric cost. View the ratio as a lifecycle decision, not a purchase one.

Emission and compliance parameters

Outlet concentration is what permits and neighbours care about. The table links the controllable inputs to the stack result so the design team can defend the number.

Controllable inputTargetResult if neglected
Air-to-cloth ratiowithin media limitRising outlet at peak
Tube sheet sealzero bypassDirect emission leak
Cake stabilityavoid over-cleanLoss of fine capture
Bag inspectionregular trendLate failure discovery
Inlet distributioneven across rowsLocal overload

Specification checklist for a request for quote

Before sending a specification, confirm each line is filled with measured data. A complete sheet returns a comparable quote and avoids silent upgrades that appear later as change orders.

  • ✓ Gas flow stated as measured peak with spare percentage noted.
  • ✓ Inlet dust concentration and particle size distribution attached.
  • ✓ Peak and average temperature and moisture recorded.
  • ✓ Required outlet emission limit written as a number.
  • ✓ Explosion classification and any venting needs declared.
  • ✓ Utility limits for compressed air and power stated.
  • ✓ Site constraints such as footprint, height and access given.
  • ✓ Expected bag life and service interval defined as goals.

How to read the specification tables together

The tables are linked. Start from airflow and dust type to pick an air-to-cloth ratio, use it with the model series table to size filter area, then confirm the media table supports the temperature and chemistry, and tune the cleaning and utility tables to the plant systems. Reading them in isolation is how mismatches slip through.

“Specifications are promises written in numbers. If the air-to-cloth ratio, the media ceiling and the cleaning pressure do not agree, the collector will tell you so every hour it runs.” — Daniel Foster

Frequently Asked Questions

What air-to-cloth ratio should a pulse bag filter use?

It depends on the dust. Coarse, free-flowing materials such as wood or grain run near two point five to three point five metres per minute, while fine, sticky or high-temperature dust needs roughly zero point eight to two point zero. Start from the dust type.

How much filter area do I need for a given airflow?

Divide total airflow in cubic metres per hour by the chosen air-to-cloth ratio in metres per minute after unit conversion, then add spare capacity. A twenty thousand cubic-metre-per-hour stream at two metres per minute needs about one hundred sixty seven square metres before spare.

Which filter media suits the highest temperature?

PTFE membrane and suitably finished fiberglass both reach about two hundred sixty degrees Celsius, with P84 and aramid covering the two hundred to two hundred forty range. Choose by chemical resistance and release, not just temperature.

Why does cleaning pressure matter so much?

The pulse must release the dust cake along the full bag length. If supply pressure sags, the lower bags stay loaded and pressure drop climbs. Steady, dry, oil-free air at the valve is the foundation of good cleaning.

How do I keep outlet emissions low?

Hold a stable dust cake by avoiding over-cleaning, seal the tube sheet so no bypass occurs, and size the air-to-cloth ratio for the permit limit with margin.

Can one model series cover very different duties?

Within a family, yes, by changing bag length, chamber count and media. But a tiny workshop unit and a large mineral plant are better served by different series, which is why the comparison table groups them by capacity.

What compressed air quality is required?

Dry and oil-free, with a pressure dew point at least ten degrees below the lowest operating temperature and oil content below one milligram per cubic metre. Wet or oily air wets the media and packs the cake, which extra pulse pressure will not fix.

How often are bags changed in a pulse system?

There is no calendar date. Replacement follows the pressure and emission trend: when differential pressure rises despite good cleaning, or outlet concentration climbs, or inspection shows hardening and holes.

Daniel Foster

Senior Dust Collection Engineer, Botou Yilida Environmental Protection Equipment

Daniel Foster is a senior dust collection engineer with more than fourteen years spent designing and commissioning baghouse and cartridge systems for metalworking, cement, food and chemical plants. He focuses on filter media selection, differential-pressure control and practical maintenance routines that keep emissions steady.


Copyright © 2025-2026 Botou Yilida Environmental Protection Machinery and Equipment Co., Ltd All Rights Reserved

contact
Contact us contact
Contact Form
  •  Can't see clearly? Click to replace